Positively Thermo‐Sensitive Monodisperse Core–Shell Microspheres

In this paper, we report on a novel family of monodisperse thermo‐sensitive core–shell hydrogel microspheres that is featured with high monodispersity and positively thermo‐responsive volume phase transition characteristics with tunable swelling kinetics, i.e., the particle swelling is induced by an increase rather than a decrease in temperature. The microspheres were fabricated in a three‐step process. In the first step, monodisperse poly(acrylamide‐co‐styrene) seeds were prepared by emulsifier‐free emulsion polymerization. In the second step, poly(acrylamide) or poly[acrylamide‐co‐(butyl methacrylate)] shells were fabricated on the microsphere seeds by free radical polymerization. In the third step, the core–shell microspheres with poly‐ (acrylamide)/poly(acrylic acid) based interpenetrating polymer network (IPN) shells were finished by a method of sequential IPN synthesis. The proposed monodisperse core–shell microspheres provide a new mode of the phase transition behavior for thermo‐sensitive “smart” or “intelligent” monodisperse micro‐actuators that is highly attractive for targeting drug delivery systems, chemical separations, sensors, and so on.     

金刚石薄膜中晶粒尺寸的研究

扫描电子显微研究表明，化学汽相沉积的金刚石薄膜中晶粒大小比较均匀。但随着沉积时间和薄膜厚度的增加，晶粒逐渐变大，且每一层内，存在少量的大金刚石颗粒，讨论了晶粒尺寸变化和大晶粒形成的原因和机制。     

Paste Residence Time in a Spouted Bed Dryer. II: Effect of Spout Operational Conditions

Residence time distributions for an aqueous solution of 10% sodium chloride in a spouted bed dryer of inert particles were determined using the stimulus-response technique. Glass and polyethylene beads with diameters 2.6 and 3.4 mm were used as inert bodies in a cylindrical column of 14.0 cm diameter and 60° conical base. The effects of inert bodies load, air, and paste flow rates on the mean residence times and RTD were determined following 2³ factorial designs. The RTD could be correlated to the perfect mixing cell model with R² varying from 0.8684 to 0.9815. The mean residence times in CSBD varied from 10.8 to 13.9 and 10.7 to 13.3 min for glass and polyethylene beads, respectively. For both inert particles, mean residence times increased with bed height and decreased with paste feed rates. Also, terms of interaction among the factors were significant in some cases, showing a complex behavior of paste residence times. Equations obtained by response surface regression could predict mean residence times on glass and polyethylene beads with deviations lower than ±10%.     

THERMAL RADIATION EFFECTS ON THE COMBUSTION BEHAVIOR OF POROUS CHAR PARTICLES

The effects of thermal radiation on the pseudosteady state and transient behavior of porous char particles exposed to an oxygen containing environment are investigated. The numerical simulation results show that particles that do not interchange radiant energy with their environment are characterized by wider ambient temperature regions where multiple steady states exist, higher combustion rates, and lower burning times     

DRYING OF GRANULAR PARTICLES IN A MULTISTAGE INCLINED FLUIDIZED BED WITH MECHANICAL VIBRATION

A mathematical model for the drying rate of granular particles in a multistage inclined fluidized bed(IFB) is presented from the standpoint of simultaneous heat and mass transfer, with taking the effect of mechanical vibration added vertically into consideration.

Steady-state distributions for the temperatures and concentrations of the particles and the heating gas, and for the moisture content of the particles are numerically calculated based on the present model. The calculated results show fairly good agreement with the experimental data, which were obtained from the drying experiments of brick particles in a three-stage IFB using comparatively low temperature air(40-60°C) as the heating gas.

It has been found within the range of the experimental conditions employed that, the mechanical vibration added vertically enhances the over-all drying rate of the particles and its effect can be considered equivalent to an increase in the air velocity.     

Recent developments of high-performance NEOMAX magnets

For further improvement in achieving extremely high magnetic properties of Nd- Fe- B sintered magnets, extensive investigation has been done to densify the magnet up to the theoretical value, to increase the volume fraction of the Nd ₂Fe₁₄B matrix phase, and to achieve a high degree of alignment. By controlling chemical composition and the amount of constituent phases,improving particle size distribution, and adopting the isostatic pressing method to get better alignment of fine particles, we have succeeded in obtaining a high-performance magnet having residual flux density (B_r) of 1.495 T (14.95 kG), maximum energy product [(BH)_max] of 431 kj/m³ (54.2 MGOe), and intrinsic coercivity (iH_c) of 845 kA/m (10.62 kOe).     

羰基铁类随机混合吸波材料等效电磁参数的计算

本文为计及多重散射偶极子间的相互作用，引入参量εｈ和μｈ，导得一组公式。它不仅能计算铁氧体类也能计算羰基铁类的随机混合吸波材料的等效电磁参数，均与实验结果吻合良好。     

Ti/Al Interaction and Austenite Grain Control in Crankshaft Manufacturing with 38MnSiVS5 Steel

38MnSiVS5 steel is similar to 38MnVS6 steel (EN), the difference being the addition of a small Ti content. Typical Ti and Al contents in the chemical composition of 38MnSiVS5 steel are Ti=0.020 and Al=0.035 mass%. Both elements combine easily with nitrogen, especially Ti, and it has been observed that relatively high Al levels are harmful for austenite grain size control at reheating temperatures. In this work 38MnSiVS5 steel is used to manufacture a large number of castings, varying only the Ti and Al contents and obtaining ingots with a different Ti/Al ratio in each case. The results show that abnormal growth of the austenitic grain occurs irrespective of the Ti and Al contents, due fundamentally to the partial dissolution and coarsening of TiN precipitates. However, the steels with high Al contents present worse behaviour due to the formation of a second type of precipitates, namely AIN, which quickly dissolve between 1000 and 1100°C, causing a drastic decline in local pinning forces that gives rise to more pronounced abnormal growth of the affected grains.     

A Micellar Route to Ordered Arrays of Magnetic Nanoparticles: From Size‐Selected Pure Cobalt Dots to Cobalt–Cobalt Oxide Core–Shell Systems

Starting with Co‐salt‐loaded inverse micelles, which form if the diblock copolymer polystyrene‐block‐poly(2‐vinylpyridine) is dissolved in a selective solvent like toluene and CoCl₂ is added to the solution, monomicellar arrays of such micelles exhibiting a significant hexagonal order can be prepared on top of various substrates with tailored intermicellar distances and structure heights. In order to remove the polymer matrix and to finally obtain arrays of pure Co nanoparticles, the micelles are first exposed to an oxygen plasma, followed by a treatment in a hydrogen plasma. Applying in‐situ X‐ray photoelectron spectroscopy, it is demonstrated that: 1) The oxygen plasma completely removes the polymer, though conserving the original order of the micellar array. Furthermore, the resulting nanoparticles are entirely oxidized with a chemical shift of the Co 2p_3/2 line pointing to the formation of Co₃O₄. 2) By the subsequent hydrogen plasma treatment the nanoparticles are fully reduced to metallic Co. 3) By exposing the pure Co nanoparticles for 100 s to various oxygen partial pressures pequation/tex2gif-inf-5.gif, a stepwise oxidation is observed with a still metallic Co core surrounded by an oxide shell. The data allow the extraction of the thickness of the oxide shell as a function of the total exposure to oxygen (pequation/tex2gif-inf-7.gif × time), thus giving the opportunity to control the ferromagnetic–antiferromagnetic composition of an exchange‐biased magnetic system.